|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-04-2011, 01:44 PM
|
#1 | ||
|
Regular Member
Join Date: Jan 2008
Location: Australia
Posts: 187
|
Hi guys....
I have noticed that the top part of the door panels of our AU (where it joins the sill / window) are getting wavy. It's not extremly bad but its noticeable and i am a picky person which spots every tiny detail thats not right. I am sure it has got something to do with the age, temperature , sun exposure etc. I was wondering if a trimmer could make it all nice again without damaging the soft and squishy vinyl part. I suppose if you warm up the panel with warm air and carefully bend it and straight it out it could work..but what do I know...its just a theory. Would be happy to get some ideas...thanks guys cheers The Moose |
||
|
|
|
02-04-2011, 02:14 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Location: ACT
Posts: 4,028
|
got a pic of it?
|
||
|
|
|
|
02-04-2011, 03:12 PM
|
#3 | ||
|
Regular Member
Join Date: Jan 2008
Location: Australia
Posts: 187
|
Hi there...
not at the moment but I'll try to make one... Its like the top part of the door panel.... when you open the door and you let your view glide alongside the top of the door panel you can see that it is wavy. The Moose |
||
|
|
|
|
02-04-2011, 04:02 PM
|
#4 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Location: ACT
Posts: 4,028
|
I can get a pic of a door trim off the car so you can see what it is like on the underside; should be a matter of re-streching and gluing the vinyl.
|
||
|
|
|
|
02-04-2011, 05:01 PM
|
#5 | ||
|
Regular Member
Join Date: Jan 2008
Location: Australia
Posts: 187
|
Hi there...
It is not the vinyl itself ..it is the black hard panel of the trim....the one where the vinyl is glued on. Thats the wavy bit. I just mentioned the vinyl because if it was possible to even out the wavy parts of the black hard plastic base of the door panel with heat, it might damage the vinyl...you know ? See...if I press the uneven part down it looks even...but as soon as I take my finger off it restores that uneven position... just imagine that line is the top of the door panel it doesn't look like that: __________________________________________________ _ it looks like that: ________________----_______________---_______________ there are uneven parts of it and its not the vinyl that got disconnected of the hardplastic base...it is the base itself that is slightly deformed (sun exposure?, age? ) The Moose |
||
|
|
|
|
02-04-2011, 05:09 PM
|
#6 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
hard to advise without pics
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
|
|
|
Is that a job for the trimmer ?
Linear Mode
