![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
Hi all just pulled my intake and rocker covers off today, I'm getting the rocker covers painted and I want to polish the intake what is the best way to do it, or would it be better to pay someone,
Also do all Au 5lts have GT40p heads just asking because when I took my roker covers off to my suprize is a cast stamp
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#2 | |||
AFF's 1st DM.......
Join Date: Dec 2004
Location: Wha???... There is only 2 states 2 be in.. WA or Drunk..
Posts: 6,200
|
gt40p's will have a cast stamp. normal 5.0l heads will have E7@$%%@#
__________________
FORD GIVING POWER TO THE PEOPLE Alloy headed 347ci EDXR8 13.21 @107.7mph Quote:
![]() |
|||
![]() |
![]() ![]() |
![]() |
#3 | |||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
Quote:
yeah mine say GT40p just wasn't sure if all au 5lts had them or not
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
|||
![]() |
![]() ![]() |
![]() |
#4 | |||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Quote:
__________________
2024 F150 XLT
|
|||
![]() |
![]() ![]() |
![]() |
#5 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
so dose any1 no what to use to polish the intake
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#6 | ||
With da Warlords
Join Date: May 2006
Location: Orange NSW
Posts: 1,781
|
A dremel is really handy. Then a %&*# load of sandpaper, buffer and some metal polish will do the trick. Not a fun job though, takes a lot of time and patience. I'm never doing it again.
These are some photos from a couple of months ago, when I had the job half finished. I should take some more now, cause I have finished polishing it all now, including the alternator. ![]() ![]()
__________________
You don't have to be faster than the bear, you just have to be faster than the slowest guy running from the bear. For Sale: Parachute. Only used once, never opened, small stain. Windsor Warlords AU III XR-8220 ![]() ![]() XR50T Ute - 300rwkw (give or take depending on the day)
![]() |
||
![]() |
![]() ![]() |
![]() |
#7 | ||
Old enough to know better
Join Date: Apr 2005
Location: Melbourne
Posts: 2,311
|
Get a quote on taking it to a polisher....wouldn't be a lot I wouldn't think....and if the quote is good enough, you won't even bother doing it yourself
__________________
Manual 2003 Machine Silver 5 Door LR Focus Zetec. Mods: Ford Racing CNC'd cylinder head milled .040", 3 angle valve grind. Ford Racing Stage II camshafts. Ford Racing cam gears. Ford Racing long tube header. Random Technology hi flow cat. Herrod 2.25" stainless cat-back. Pipercross Viper intake. CFM 65mm throttle body. 2000 ported intake manifold. Herrod Custom SCT tune. Eibach suspension. Quaife ATB diff. Wilwood 13" brakes. Custom ST170 leather interior. www.cardomain.com/ride/2773918
|
||
![]() |
![]() ![]() |
![]() |
#8 | ||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
James do my alterator, its the only other bit I want done!
It is a of a job to do.
__________________
2024 F150 XLT
|
||
![]() |
![]() ![]() |
![]() |
#9 | |||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
Quote:
yeah got a quote today $160.00, I think I'll do it myself
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
|||
![]() |
![]() ![]() |
![]() |
#10 | |||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
Quote:
What metal polish did you use? I've got autosol and purple
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
|||
![]() |
![]() ![]() |
![]() |
#11 | ||
With da Warlords
Join Date: May 2006
Location: Orange NSW
Posts: 1,781
|
I used autosol, but theres no point using it till your right at the end of the job. Grab a dremel to remove most of the roughness. I found the sanding belts worked well here, then work up your way up in sandpaper. I started with 180 grit then went up from there, till there were no scratches present from the previous grit. (This is important at the end for a good finish)
I used 180, 320, 400, 600, 800, 1000, 1200, 1500. Once finished with that, then I hit it with autosol, and a buffing wheel in the dremel again.
__________________
You don't have to be faster than the bear, you just have to be faster than the slowest guy running from the bear. For Sale: Parachute. Only used once, never opened, small stain. Windsor Warlords AU III XR-8220 ![]() ![]() XR50T Ute - 300rwkw (give or take depending on the day)
![]() |
||
![]() |
![]() ![]() |
![]() |
#12 | |||
With da Warlords
Join Date: May 2006
Location: Orange NSW
Posts: 1,781
|
Quote:
![]() ![]()
__________________
You don't have to be faster than the bear, you just have to be faster than the slowest guy running from the bear. For Sale: Parachute. Only used once, never opened, small stain. Windsor Warlords AU III XR-8220 ![]() ![]() XR50T Ute - 300rwkw (give or take depending on the day)
![]() |
|||
![]() |
![]() ![]() |
![]() |
#13 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
I got the rocker covers back yesterday, and I've sent a few more bits and pieces off, I just finished polishing my power steering pump looks unreal ( you can't see yours I don't have the cover) , I keep avoiding the intake I started a little of it, starting to look good all ready. My dad got all the crap I need from work but not the 1500 I best get me some...............
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#14 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
Finally finished the intake its polished, rocker covers painted, power steering bracket polished and a few bits powder coated, to top it all off, finished it around an hour ago even better it started, will post some pics tomorrow........
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#15 | ||
FF.Com.Au Hardcore
Join Date: Jan 2005
Posts: 1,463
|
Do you have any pics, i would like to see if the results using a dremel are worth it.
|
||
![]() |
![]() ![]() |
![]() |
#16 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
all finished back on the car came up really well looks good with the rocker covers painted to, wil get some pics of the hole engine bay soon,
![]()
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#17 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
I couldn't get in the grooves on the side so I painted it black and then sanded/grinded the top, I used a drill with really course scotch brite type pads and worked down 3 stages, wet rubbed, then polished with with a pad on the drill (PURPLE POLISH)
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#18 | ||
Miami Pilot
![]() Join Date: Jan 2005
Location: ACT
Posts: 21,701
|
Are you going to clear coat it to keep the finish? If not, you will need to polish it regularly to keep it looking that good.
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
![]() |
![]() ![]() |
![]() |
#19 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
well it's allready back on the car, so it looks like I will have to polish it every now and again, unless I just mask around it and do it in the engine bay
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |
![]() |
#20 | ||
FF.Com.Au Hardcore
Join Date: Jun 2005
Location: in a house
Posts: 789
|
just wondering if any1 has or knows where to get the chrome intake pipe?
__________________
Its not peer presure..........Its just your turn! XE project underway ![]() |
||
![]() |
![]() ![]() |